|
Load Ratings |
|
|
Dimmer Channels |
6 |
|
|
Maximum Per Channel |
800 Watts/VA (3.5 Amps @ 230 Volts AC), expandable via Expansion Modules (sold separately) |
|
|
Minimum Per Channel |
25 Watts/VA (0.108 Amps @ 230 Volts AC) |
|
|
Module Total |
2200 Watts/VA (10 Amps @ 220 Volts AC);
2300 Watts/VA (10 Amps @ 230 Volts AC);
2400 Watts/VA (10 Amps @ 240 Volts AC) |
|
|
Load Types |
LED[1], Incandescent, Magnetic Low-voltage, Neon/Cold Cathode, 2-Wire Dimmable Fluorescent, & Non-Dim Lighting (also: Electronic Low-voltage, 3 and 4-Wire Fluorescent, High-Inrush Switching, & 277V via CLS-EXP Series expansion modules) |
|
Power Requirements |
|
|
220 to 240 Volts AC, 50/60Hz line power |
|
Connections |
|
|
LOCAL DEVICES |
(1) 4-pin 5mm detachable terminal block;
Cresnet Master port for local devices including: CNPWS-75
-
C2N-DB and CNX-B Series keypads, 16 maximum;
-
C2N-SSC-2 and C2N-SDC-DC shade controllers; 16 maximum;
-
Additional CLSI-C6 or CLSI-C6M units, 8 maximum;
Additional or other Cresnet power supply required beyond 4 devices; C2N-SDC-DC always requires an additional power supply
|
|
|
HOT |
(1) Captive screw terminal[2], line power input |
|
|
LOAD1 – LOAD6 |
(6) Captive screw terminals[2], dimmer channel outputs 1 – 6 |
|
|
NEUTRAL |
(1) Captive screw terminal[2] |
|
|
GROUND |
(1) Captive screw terminal[2] |
|
|
PC (front) |
(1) 3.5mm TRS mini-phone jack, RS-232 Programming port |
|
Controls |
|
|
Buttons 1 – 6 |
(6) 3-position rocker pushbuttons; configurable to recall (or toggle recall/off) individual scenes, control shades, or for master lighting or shade control; “scene mastering” option enables manual dimming utilizing rocker button action; also used to adjust lighting levels when in “Lighting” mode and shade positions when in “Shades” mode; additional functionality configurable via software |
|
|
Up/Down Button |
(1) 3-position rocker pushbutton; configurable for master lighting or shade control, or as a “shift” for Buttons 1-6; additional functionality configurable via software |
|
|
ON |
(1) pushbutton, recalls “On” scene |
|
|
OFF |
(1) pushbutton, turns all lights off |
|
|
LIGHTS, SHADES |
(2) Pushbuttons, select “Lights” or “Shades” modes |
|
|
SAVE, CANCEL, ∧, ∨ |
(4) Pushbuttons, navigate and execute setup functions |
|
|
Reset |
Recessed miniature pushbutton for hardware reset |
|
|
Dimming Ramp Rate |
5 seconds (default), software adjustable 1 to 10 seconds |
|
|
Scene Fade Time |
2 seconds (default), software adjustable 0 seconds to 99 minutes |
|
LED Indicators |
|
|
Scenes |
(6-white) Correspond with each “Scene” Button |
|
|
High/Low |
(2-white) Indicate “Shift” status |
|
|
ON |
(1-white) Indicates “On” Scene is selected |
|
|
LIGHTS, SHADES |
(2-green) Indicates “Lights” or “Shades” mode is active |
|
|
SAVE, CANCEL |
(2-green) Correspond with “Save” and “Cancel” Buttons |
|
|
MIN, SEC |
(2-green) Indicates display of “Minutes” or “Seconds” |
|
|
1 – 6 |
(6-green) 7-Segment bargraphs, indicate lighting levels and shade positions |
|
|
Numeric Display |
(2-green) 8-Segment digits, indicates modes and setup values |
|
IR Receiver |
|
|
Reception Frequency |
36 kHz |
|
|
Requires CLS-IRHT8 IR remote |
|
Motion Detector |
|
|
Type |
Infrared |
|
|
Range |
20 to 30 feet at 4 foot elevation |
|
RF Wireless |
|
|
RF Transceiver |
2-way RF, 2.4 GHz ISM Channels 11-26 (2400 to 2483.6 MHz), IEEE 802.15.4 compliant |
|
|
Range (typical) |
150 feet indoor, 250 feet outdoor;
Subject to site-specific conditions; range is increased by adding additional devices or C2NI-MNETRPT repeater |
|
|
Gateway |
Requires a C2N-MNETGW RF gateway |
|
Environmental |
|
|
Temperature |
32° to 104°F (0° to 40°C) |
|
|
Humidity |
10% to 90% RH (non-condensing) |
|
Enclosure |
|
|
Mounts in a 4-gang electrical box, 3-1/2" deep minimum |
|
Dimensions |
|
|
Height |
4.48 in (11.38 cm) |
|
|
Width |
8.89 in (22.58 cm) |
|
|
Depth |
2.60 in (6.61 cm) |
|
Weight |
|
|
1.43 lb (0.65 kg) |
