CLS-EXP-DIM

燈光控制系列

Works with Crestron iLux®, CLW^[2], DIN, and CLX series dimmers
Emulates the characteristics of the dimmer that is controlling it

The CLS-EXP-DIM enables the expansion of Crestron iLux® Integrated Lighting System (CLS-C6 series) and other Crestron® lighting dimmers to support 120, 230, or 277 Volt loads up to 16 Amps. It allows any output channel of the iLux system to dim a fully loaded circuit of LED^[1], incandescent, magnetic low-voltage, neon/cold cathode, or 2-wire dimmable fluorescent lighting loads. It is also compatible with CLW-Series^[2] in-wall dimmers and select CLX-Series lighting control modules^[3].

The CLS-EXP-DIM is designed for mounting to a vertical surface^[4], and can be installed in an environmental air-handling space above a suspended ceiling. Conduit knockouts are provided on the bottom and lower sides. All connections are made via screw terminals behind the front cover.

Load Ratings
	Dimmer Channels	1
	Load Rating	16 Amps
	Minimum Load	15 Watts at 120 Volts, 25 Watts at 230 Volts, 30 Watts at 277 Volts
	Load Types	LED^[1], incandescent, neon/cold cathode, magnetic low voltage, 2-wire dimmable fluorescent (Advance Mark 10 Powerline® or equivalent)
Input Voltages
	Line Power	120 to 277 Volts AC, 50/60 Hz
	Control Input	120 or 230 Volts AC, 50/60 Hz, phase independent of line power and load
Connections
	INPUT, CTRL	(1) Captive screw terminal^[5], control input from CLS(I)-C6 Series, CLW-DIM Series^[2], CLX(I)-DIM Series, GLX-DIM6, GLXX-2DIM8, DIN-1DIM4, or DIN-1DIMU4 dimmers; Note: Presents a 25 Watt load to the controlling dimmer; a maximum of 5 CLS-EXP-DIM modules may be connected to the controlling dimmer, which cannot be wired to control any other loads besides the CLS-EXP-DIM modules
	INPUT, NEUT	(1) Captive screw terminal^[5], neutral connection for control input
	OUTPUT, DIM OUT	(1) Captive screw terminal^[5], dimmed load output
	OUTPUT, (NC)	(1) Captive screw terminal^[5], not used (do not connect)
	OUTPUT, HOT	(1) Captive screw terminal^[5], line power input
	OUTPUT, NEUT	(1) Captive screw terminal^[5], neutral connection for line power input and load
	GROUND	(1) 3-terminal chassis ground bus bar
Controls & Indicators
	FLUORESCENT OFF THRESHOLD	(1) recessed screwdriver-adjustable trim pot behind removable cap, adjusts minimum brightness level
	STATUS	(1) Red LED behind front panel, illuminates when load output is on
	POWER	(1) Green LED behind front panel, indicates line power is applied to the HOT terminal
Environmental
	Temperature	32° to 104°F (0° to 40°C)
	Humidity	10% to 90% RH (non-condensing)
	Heat Dissipation	140 BTU/Hr at maximum load, 16A
Enclosure
	Surface mount^[4] module with (2) integral mounting flanges, galvanized steel w/gray matte powder coat front panel, extruded aluminum heat sink, (4) 1/2” or 3/4” conduit knockouts provided on bottom and lower left & right sides
Dimensions
	Height	8.82 in (224 mm)
	Width	6.39 in (163 mm)
	Depth	3.18 in (81 mm)
Weight
	3.34 lb (1.52 kg)