CLS-EXP-DIMFLV

燈光控制系列

Works with Crestron iLux®, CLW^[1], DIN, and CLX series dimmers
Emulates the characteristics of the dimmer that is controlling it

The CLS-EXP-DIMFLV enables the expansion of Crestron iLux® Integrated Lighting System (CLS-C6 series) and other Crestron® lighting dimmers to allow control of 0-10 Volt fluorescent dimming ballasts. It can also be used to switch non-dimmable loads including LED, incandescent, MLV, ELV, HID, fluorescent ballasts, and motors. A single model supports 120, 230, or 277 Volt loads up to 16 Amps.

Any output channel of the iLux system can be used to control the CLS-EXP-DIMFLV to dim a fully loaded circuit. It is also compatible with CLW-Series^[1] in-wall dimmers and select CLX-Series lighting control modules^[2]. The metal enclosure is designed for mounting to a vertical surface^[3], and can be installed in an environmental air-handling space above a suspended ceiling. Conduit knockouts are provided on the bottom and lower sides. All connections are made via screw terminals behind the front cover.

Load Ratings
	Dimmer Channels	1
	Load Rating, Lamp	16 Amps @ 120 to 277 Volts
	Load Rating, Motor	0.5 HP @ 120 Volts, 1 HP @ 230/277 Volts
	Minimum Load	15 Watts @ 120 Volts, 25 Watts @ 230 Volts, 30 Watts @ 277 Volts
	Dim Load Types	0-10V Dimmable Fluorescent Ballasts, Advance Mark 7 or other compliant with specifications for control by DC voltage per ANSI C82.11:2002 and IEC60929:2006
	Switch Load Types	LED, incandescent, fluorescent, magnetic low voltage, electronic low voltage, neon/cold cathode, high-intensity discharge (HID), motors
Input Voltages
	Line Power	120 to 277 Volts AC, 50/60 Hz
	Control Input	120 or 230 Volts AC, 50/60 Hz, phase independent of line power and load
Connections
	INPUT, CTRL	(1) Captive screw terminal^[4], control input from CLS(I)-C6 Series, CLW-DIM Series^[1], CLX(I)-DIM Series, GLX-DIM6, GLXX-2DIM8, DIN-1DIM4, or DIN-1DIMU4 dimmers; Note: Presents a 25 Watt load to the controlling dimmer; a maximum of 5 CLS-EXP-DIMFLV modules may be connected to the controlling dimmer, which cannot be wired to control any other loads besides the CLS-EXP-DIMFLV modules
	INPUT, NEUT	(1) Captive screw terminal^[4], neutral connection for control input
	OUTPUT, SW OUT	(1) Captive screw terminal^[4], switched load output
	OUTPUT, HOT	(1) Captive screw terminal^[4], line power input
	OUTPUT, NEUT	(1) Captive screw terminal^[4], neutral connection for line power input and load
	0-10V +/-	(2) Captive screw terminals^[4], dimming control output; Class 1 or Class 2 wiring allowed; Control Voltage: 0-10 Volts DC, 70 mA
	GROUND	(1) 3-terminal chassis ground bus bar
Controls & Indicators
	STATUS	(1) Red LED behind front panel, illuminates when load output is on
	POWER	(1) Green LED behind front panel, indicates line power is applied to the HOT terminal
Environmental
	Temperature	32° to 104°F (0° to 40°C)
	Humidity	10% to 90% RH (non-condensing)
	Heat Dissipation	70 BTU/Hr at maximum load, 16A
Enclosure
	Surface mount^[3] module with (2) integral mounting flanges, galvanized steel w/gray matte powder coat front panel, extruded aluminum heat sink, (4) 1/2” or 3/4” conduit knockouts provided on bottom and lower left & right sides
Dimensions
	Height	8.82 in (224 mm)
	Width	6.39 in (163 mm)
	Depth	3.18 in (81 mm)
Weight
	3.34 lb (1.52 kg)